Pianos routinely make movers yearly list of products that are most often harmed. Grand pianos are especially bothersome. Practicing the following procedures for dismantling, cushioning and loading grand pianos will prevent damage, lower claims cost, and improve consumer satisfaction.
1) At least three people are needed to handle an infant grand piano. If the infant grand piano requires to increase or down stairs or if a complete or performance grand piano needs to be transferred, a minimum of 4 individuals are needed.
2) Always complete a precise and extensive stock. It might be essential or more effective to use a visual stock to effectively explain and show pre-existing damage.
3) As numerous parts are taken apart, please place all hardware in an appropriately labeled parts bag and then place the parts bag in a "Parts Box".
4) Remove the music rack (lyre) from its track by pulling it towards the keyboard. Wrap it in a tidy furniture pad.
5) Disconnect the cover by eliminating the hinge pins. Have one person wiggle the lid, holding it opposite the hinge, while a 2nd person works the pin loose. Please take care not to damage the wood with the pliers or with the pin itself. Cover the jaws of the pliers with a small cloth to assist prevent damage to the wood if essential. Wrap the lid in a tidy furniture pad.
6) Eliminate the prop that holds the cover open and wrap it in a tidy furniture pad. The prop has a hinge pin and remains in 2 pieces.
7) Eliminate the pedal assembly and wrap it in a tidy furniture pad. The braces at the back of the assembly rest in slots at each end. When eliminating the screws, please take care not to drop the braces. In addition, please be especially cautious with the push-rods so that they will not get bent. As you deal with the piano, number the push-rods from delegated right as "1", "2", and "3", by placing a piece of masking tape with the proper number on each rod. Note: If masking tape is unavailable, please use properly identified parts bags for this function. When reassembling at location, please be sure to put the rods in the appropriate order so that the pedals will work effectively.
8) Pad the piano by positioning a tidy rolled furnishings pad (stretch-wrap the pad to prevent it from unrolling) on the anchor cover of the keyboard to avoid it from flopping open while you handle the piano. Keep in mind: Please guarantee that the surface of the piano is dust-free prior to padding it.
9) Position a piano board and connect the straps so that it is all set to receive the piano. The raised brace on the piano board must be at the keyboard end of the piano.
10) Remove the left front leg by placing one individual underneath the piano at the left end of the keyboard. Be sure to have two people lifting the corner of the piano while the third person removes the leg. Keep in mind: Please be sure to keep in mind which legs were gotten rid of from which positions given that some pianos have legs that are not interchangeable.
11) Place the piano on the piano board by decreasing the "leg-less" end onto the board. Please be sure to lift the entire piano a little while completing this maneuver to prevent excessive pressure on the staying, attached legs as the piano ideas. Be sure that get more info the piano is centered comfortably against the brace at the end of the piano board.
12) Get rid of the 2 remaining legs and cover them in clean furnishings pads. These legs are held in place by a "key and slot" arrangement. To get rid of the leg, slide it inward towards the center of the piano until it comes out of the slot.
13) Protect the piano to the piano board by bringing completions of the straps together and securing them. Location folded burlap pads over the furniture pads but under the straps to supply additional defense to the edges of the piano. To prevent the strap near the narrow end of the piano from slipping off, connect the loose ends of the 2 straps together.
14) To move the piano over a flat, level surface, tilt the piano and piano board and place a four-wheel dolly under the center of the piano board.
15) To move the piano up or down stairs, utilize the piano board as a skid. After adequately padding the stairs for protection against house damage, place the keyboard end of the piano toward the bottom of the stairs. Attach a hump strap to the leading end of the piano board to avoid the piano from slipping.
16) To fill the piano, leave it on the piano board and location it in a tier as the very first base product with the keyboard facing the wall of the preceding tier. The very best location to fill the cushioned cover is in between the piano and the preceding tier or between the piano and the wall.
Although grand pianos represent a considerable challenge, they can be moved without damage by utilizing common sense and practicing the procedures listed above.